Home Addition Plus

Helping Homeowners Every Day

 
    Home How-To Store Ebooks    Bid Sheets HouseSight About Us Contact

 

 
 

    

 

                             

How to Tile a Custom Shower Ebook  

 

Home Improvement Tools from Amazon

 

Visit My

Amazon

Tool Store

 

                           

 

 

   

 

Corner Shower Stall Installation

How to Install a Corner Shower Stall and Shower Door Enclosure

By: Mark J. Donovan

Corner shower stalls are ideal for smaller bathrooms. They are also perfect for large bathrooms where there is a desire for a Jacuzzi tub and a separate shower unit. Corner shower stall units are meant specifically to maximize limited bathroom floor space. Prefab fiberglass corner shower stalls or corner shower pans typically come in triangular shapes, but can also be found in quarter-round footprints as well. Custom ceramic tile showers used in corner applications are often designed with triangle, square or rectangular footprints.

 

Besides utilizing less floor space, prefab corner shower stall enclosures are much less expensive than full tub/shower units. Also, due to the fact that they are smaller, they are easier to handle and install when doing a bathroom remodeling project. Often it is impossible to carry in and install a combination tub shower unit into an existing home due to door and hall width limitations.

 

Corner Shower Stall Installation


Corner shower stall installation is fairly straight forward, particularly if installing a prefab fiberglass corner shower stall unit. Prefab fiberglass corner shower stall units can come as one complete assembly including the base and side walls, or it can come in sections. Sectional ones include a separate triangular shaped corner shower pan base and sidewalls. Each type of corner shower unit comes with predrilled holes for the drain and plumbing fixtures.

 

Note: It is important to make sure you have communicated to the plumber the specific location and hole openings for the particular corner shower stall you plan on installing, so that the plumber can properly rough in the drain and plumbing fixture assemblies before installing the corner shower unit.

The first step in installing a corner shower stall is to install the drain assembly hardware to the base of the corner shower pan unit and connect the drain pipe to it. Typically there is a rubber compression fitting associated with the drain assembly hardware that is slid over the drain pipe to create a leak free seal. The corner shower pan unit is then fastened to the stud walls with the appropriate clips or corrosive resistant screws that come with the corner shower pan kit.

 

Find a Qualified Bathroom Remodeling Contractor in Your Area

Get Free Quotes.  Easy, Quick and No Obligations!

 

For the home improvement or home remodeling project that is too big for you, check out our partner NeedContractor. They are a national resource for finding pre-screened, insured, and licensed home improvement and remodeling contractors in your local area.

Find Local, Pre-Screened New Home Construction Contractors

 

Get Matched in 48 hours with Bathroom Remodeling Contractors!

 

Next the sidewalls are attached to the wall studs and over the corner shower pan base using the fasteners included in the kit, or corrosive resistant screws. Make sure to apply a bead of bathroom silicone caulk at the seams where the side walls lap over the corner shower stall base and between adjacent sidewalls. This will help to ensure a leak free corner shower stall.

After installing the corner shower pan base and back walls, mount the plumbing fixtures onto the wall. You may need to call in your plumber to do this portion of the project. Make sure to apply a bathroom caulk and sealer around the fixtures to prevent leakage behind the shower stall.
 

Installing Shower Door Enclosure to Corner Shower Unit


After mounting the plumbing fixtures to the corner shower stall, it’s now time to install the shower door enclosure unit. Typically framed shower door enclosures are used with prefab fiberglass corner shower stall units. Follow the manufacturer’s instructions for installing the shower door enclosure. The typical process in installing a framed shower door enclosure, however, involves centering and mounting the bottom, side and top frame plates to the shower unit walls and base, and then installing the glass shower door panels. Lastly, a bead of bathroom silicone caulk is applied around all the seams.

 

For more help on bathroom remodeling, see HomeAdditionPlus.com's Bathroom Remodeling Bid Sheet. The Bathroom Remodeling Bid Sheet provides you with the knowledge and information you need to plan a bathroom remodeling project, and what to look for when hiring contractors. It also includes a detailed cost breakdown table and a spreadsheet for estimating your own new bathroom remodeling building costs.

 

How to Finance your Bathroom Remodeling Project -  can help provide funds for your new home improvement project if financing is required.

Related Bathroom Remodeling Design Information

 

 


Corner Shower Stall Kits from Amazon.com

 
   

 


Get Free Bathroom Remodeling Price Quotes with No Obligation!

Fill out our 3-5 minute quick and easy form, and receive a free price quote on bathroom remodeling from one of our prescreened and licensed bathroom remodeling contractors. This process is free and there is no obligation to continue once you receive your bathroom remodeling price estimate.

 
     

- Corner Shower Stall Installation -

[Back to Bathroom Remodeling]

 

 

 

 

 
     

Follow HomeAdditionPlus on Twitter

to HomeAdditionPlusVideos / Subscribe to HomeAdditionPlus.com feed

Advertise / Favorite Links / SiteMap / ToS / Privacy Policy / Disclosure Policy

Copyright 2005-2012 by DIY HomeAddition Plus.com - A Do it Yourself Home Improvement Site

 

web metrics