Home Addition Plus

Helping Homeowners Every Day

 
    Home How-To Store Ebooks    Bid Sheets HouseSight About Us Contact

 

 
 

    

 

                             

Kitchen Remodeling Bid Sheet  

 

Home Improvement Tools from Amazon

 

Visit My

Amazon

Tool Store

 

                           

 

 

   

 

How to Replace a Kitchen Sink Faucet

Step by Step Instructions on Replacing a Kitchen Sink Faucet

By Mark J. Donovan

 

Our old kitchen sink faucet became so corroded we could no longer swivel it from one kitchen sink bay to the other. So I noted that it was a single hole type kitchen faucet and headed off to the local home improvement center to find a replacement for it. Replacing a kitchen sink faucet is fairly easy to do with the exception that working underneath a kitchen sink is extremely awkward. However, if you remove all the items from the kitchen cabinet directly underneath the kitchen sink you can usually find enough room in it to work.

In regards to the tools required to replace a kitchen sink faucet all you normally need is a crescent wrench and a pair of adjustable channel lock pliers.

Removing Old Kitchen Sink Faucet

After buying a replacement kitchen sink faucet I returned home and began the task of removing the old kitchen faucet. I started out by first turning off the hot and cold supply lines to the old kitchen faucet. Then using a crescent wrench I disconnected the kitchen faucet’s flexible supply line hoses that were attached to the copper supply line pipes in the kitchen cabinet. I also disconnected the spray hose line from the faucet tube it was connected to.

Next, I loosened the nut that was holding the kitchen faucet fastening plate to the underside of the kitchen countertop with a pair of channel lock pliers. Once the nut was loosened, I used my fingers to remove it from the threaded bolt it was attached to. Finally, I pulled the old kitchen sink faucet up and out of the hole in the kitchen countertop.

Prepping New Kitchen Sink Faucet for Installation

The next step in replacing my kitchen sink faucet was preparing the new one for installation. It’s better to do this work at a table than underneath the kitchen sink.

First, I threaded the spray hose through the main nozzle assembly and then I secured the nozzle itself to the main assembly. I also attached the escutcheon plate and foam gasket to the bottom of the main nozzle assembly to ensure a tight seal with the kitchen countertop.

Installing Kitchen Sink Faucet

I then slid the replacement kitchen sink faucet assembly into the kitchen countertop hole and crawled back underneath the cabinet. Once back in position underneath the new replacement kitchen sink faucet, I attached a brass washer and large mounting nut assembly to the threaded base of the faucet. I finger tightened it and then attached two locking screws to the mounting nut assembly to securely hold the faucet in place.

Here I'm replacing the old kitchen faucet sink with this new one.

Photos By Mark Donovan

Next I slipped the large spray hose weight over the spray hose and connected the loose end of the spray hose to the spray tube coming down from the base of the kitchen sink faucet.

Here are the copper supply lines that feed the kitchen sink faucet.

Here I'm sliding the spray weight over the faucet spray hose.

I then attached the hot and cold supply lines that splayed from the base of the faucet to the hot and cold water copper supply lines. I used a crescent wrench to snug them down tightly to the threaded nipples on the valve assemblies protruding from the top of the copper supply lines.

Finally, I turned the hot and cold water supply valves back on and tested my newly replaced kitchen sink faucet. As I let the water run I checked for leaks. Fortunately all went well and there were no leaks.

One Final Note

If you decide to replace your own kitchen sink faucet you may find it helpful to remove the kitchen sink drain pipes temporarily to give you a little more room to work. In my case I had sufficient room to work around them so I left them intact.

 

Find a Qualified Home Plumbing Contractor in Your Area

Get Free Quotes.  Easy, Quick and No Obligations!

 

For the home improvement or home remodeling project that is too big for you, check out our partner NeedContractor. They are a national resource for finding pre-screened, insured, and licensed home improvement and remodeling contractors in your local area.

Find Local, Pre-Screened Home Plumbing Contractor

 

Get Matched in 48 hours with Home Plumbing Contractors!

 

For information on how to install a new faucet, See HomeAdditionPlus.com's  "Installing a New Faucet Ebook". It provides in-depth, easy to understand, step-by-step instructions and pictures, on how to install a new Faucet.

Related Articles and Videos

 

 


Additional Home Plumbing Resources for Learning How to Fix a Leaky Faucet

 
       


Kitchen Sink Faucets, Faucet Valves and Tools for Replacing a Faucet from Amazon.com

     

 

 
 

-  How to Replace a Kitchen Sink Faucet  -

[Back to DIY Plumbing Tips and Ideas]

 

 

 

 

 
     

Follow HomeAdditionPlus on Twitter

to HomeAdditionPlusVideos / Subscribe to HomeAdditionPlus.com feed

Advertise / Favorite Links / SiteMap / ToS / Privacy Policy / Disclosure Policy

Copyright 2005-2012 by DIY HomeAddition Plus.com - A Do it Yourself Home Improvement Site

 

web metrics